We are using below dacs APIs in our code which is included in header file AuthRequest.h setUsageLogging getUsageLogging We need the information about these APIs and where they do generate dacs.usage file on TREP server?

Question

Question by sarvesh.singh · Jul 21, 2020 at 01:28 PM · DACS open-dacs

We are using below dacs APIs in our code which is included in header file AuthRequest.h setUsageLogging getUsageLogging We need the information about these APIs and where they do generate dacs.usage file on TREP server?

0

10 |1500 characters needed characters left characters exceeded

Attachments: Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Answer 1 · 2020-07-21T13:56:44Z

REFINITIV

Best Answer

Answer by umer.nalla · Jul 21, 2020 at 01:56 PM

Hi @sarvesh.singh

The Open DACS API C++ documentation, training material and other downloads can be accessed from the Developer Portal.

Documentation for setUsageLogging() can be found in the SDK download file or can be accessed online at the links below:

the setUsageLogging() method is explained here

The default value for setUsageLogging PerformUsage parameter is DontPerformUsageLogging

However, the other possible PerformUsage values are listed on this page.

0 · Share

10 |1500 characters needed characters left characters exceeded

Attachments: Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Answer 2 · 2020-07-21T14:34:34Z

REFINITIV

Answer by zoya faberov · Jul 21, 2020 at 02:34 PM

Hello @sarvesh.singh,

In addition to the suggestions by @Umer Nalla, you may wish to look at this previous discussion thread on the same.

If you are connecting to a remote dacs sink daemon on ADS (TREP), you have an option of creating dacs.usage on there.

0 · Share

10 |1500 characters needed characters left characters exceeded

Attachments: Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Answer 3 · 2020-07-29T14:40:21Z

Answer by sarvesh.singh · Jul 29, 2020 at 02:40 PM

Hi @zoya.farberov,@Umer Nalla, Thanks for your reply. The link provided is helpful to understand about the APIs. I am using remote dacs sink daemon on ADS and tried to generate the report over there by setting the usage param to 1(AlwaysPerformUsageLogging) but I can't see any data w.r.t. that report.

0 · Share

10 |1500 characters needed characters left characters exceeded

Attachments: Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

Answer 4 · 2020-08-03T19:38:06Z

REFINITIV

Answer by zoya faberov · Aug 03, 2020 at 07:38 PM

Hello @sarvesh.singh,

Please note, that all the steps that are discussed in the thread referred to, both from dacs administrator via dacs admin ui and via API are necessary. It is likely required to coordinate your actions with your dacs admin/market data group on this matter, in order to verify the dacs admin side of the requirement.

For the additional details on how to generate usage on the remote daemon, refer to the answer below the answer that is accepted and marked in green.

Setting the parameter is required, but is not enough.

0 · Share

10 |1500 characters needed characters left characters exceeded

Attachments: Up to 2 attachments (including images) can be used with a maximum of 512.0 KiB each and 1.0 MiB total.

We are using below dacs APIs in our code which is included in header file AuthRequest.h setUsageLogging getUsageLogging We need the information about these APIs and where they do generate dacs.usage file on TREP server?

4 Replies

Watch this question

Related Questions